product highlights the mi-series is designed for applications utilizing distributed power architecuture based on vicors 1st generation family of zero-current/zero-voltage switching, component level dc-dc converters. operating at frequencies in excess of 1 mhz, the mi-series offers state-of-the-art performance in terms of power density, efficiency, noise, ease of use, and reliability. all units are manufactured in iso 9001-registered facilities. fully encapsulated in vicors industry standard package enables the mi-series to meet mil-std-810 environmental requirements for humidity, fungus, salt, fog, explosive atmosphere, acceleration, vibration, and shock. (see page 32.) standard features such as wide output trimming/programming, current limiting, remote sense, output inhibit, and latching ovp and otp combine to offer a high degree of protection, versatility, and reliability for power systems. mi-200 tm p arameter min typ max units test conditions input characteristics input voltage range see input voltage chart no load power dissipation 1.35 2.0 watts output characteristics set point accuracy 0.5 1.0 % vnom load/line regulation 0.05 0.2 % vnom ll to hl, 10% to fl 0.2 0.5 % vnom ll to hl, nl to 10% output temperature drift 0.01 0.02 %/? output noise - pp 1.0 1.5 % vnom whichever is greater 100 150 mv 20 mhz bw output voltage trimming (1) 50 110 % vnom remote sense compensation 0.5 vdc o vp set point (2) 115 125 135 % vnom latching current limit 105 125 % inom auto restart short circuit current (3) 20 130 % inom control pin characteristics gate in high threshold 6 vdc gate in low threshold 0.65 vdc gate in low current 6 ma p ow er sharing accuracy 0.95 1.05 isolation characteristics isolation (input to output) 3,000 v rms isolation (output to baseplate) 500 v rms isolation (input to baseplate) 1,500 v rms input/output capacitance 50 75 pf environmental (mil-std-810) altitude - method 500.2 70,000 feet procedure ii humidity - method 507.2 86 / 240 % / hours procedure 1, cycle 1 acceleration - method 513.3 9 g's procedure 2 vibration - method 514.3 20 g's procedure 1, category 6 shock - method 516.3 40 g's procedure 1 reliability (mil-hdbk-217f) 25? ground benign: g.b. 2,478,477 hours 50? naval sheltered: n.s. 584,920 hours 65? airborne inhabited cargo: a.i.c. 483,303 hours thermal characteristics efficiency 80-90 % baseplate to sink 0.07 ?/w with thermal pads thermal shut down 90 95 105 ? latching baseplate operating temperature +85 ? see product grade storage temperature +100 ? see product grade mechanical specifications we ight 6.0 (170) ounces (grams) converter/booster specifications (at t bp = 25?, nominal line and 75% load, unless otherwise specified) fea tures military cots dc-dc converters 50 to 100 w (1) 10 v, 12 v, and 15 v outputs, standard trim range ?0%. consult factory for wider trim range. (2) no over temperature or voltage protection in booster modules. (3) output voltages of 5 v or less incorporate foldback current limiting; outputs of 10 v and above provide constant current limiting. inputs: 28 vdc per mil-std-704d/e 155 vdc per mil-std-1399a 270 vdc per mil-std-704d/e single output: 2 ?48 vdc up to 23 w/in 3 mil-std-810 environments up to 90% efficiency remote sense current limit o vp and thermal shut down p ow er boosters for higher power outputs zvs/zcs power architecture low noise fm control size: 4.6" x 2.4" x 0.5" (116,8 x 61,0 x 12,7 mm) } mi-200 03/04 1 of 2
configuration chart input voltage nominal range transient 2= 28 v 18 ?50 v (1) 60 v 5= 155 v 100 ?210 v 230 v 6= 270 v 125 ?400 v (2) 475 v 7= 165 v 100 ?310 v mi - 2 - semi-custom driver and booster modules available: consult factory. (1) 16 v operation at 75% load. (2) these units rated at 75% load from 125-150 vin: mi-26z-xv mi-26y-xv mi-260-xw 28 vdc input per mil-std 704d/e 155 vdc input per dod-std-1399a 270 vdc input per mil-std-704d/e product grade specifications +0.030 (0,76) -0.000 (0) product id this surface full r 5 6 7 8 9 4 3 2 1 pin # 1 2 3 4 5 6* 7* 8* 9 function +in gate in gate out -in +out +sense trim -sense -out * do not connect on booster modules aluminum base .01 0.040 (1,0) dia (7) places solder plate over copper alloy 0.080 (2,0) dia (2) places solder plate over copper alloy 0.30 0.015 (7,6) (0,38) 1.80 (45,7) 4.20 0.50 0.22 (5,6) min 0.12 4.60 2.40 1.75 0.30 0.15 (3,8) 2.10 (53,3) 0.40 (10,2) 0.35 0.015 (8,9) (0,38) 1.40 (35,6) 1.00 (25,4) 0.70 (17,8) 3.60 mi-200 mechanical drawing 0.50 (12,7) 0.15 (3,8) mi-200 (116,8) (91,4) (3,0) (7,6)min (12,7) (61,0) (44,5) (106,7) * te st data available for review or download from vicorpower.com mechanical drawing output power/current 5 v < 5 v y= 50 w 10 a x= 75 w 15 a w= 100 w 20 a v= o 30 a for additional power, 100 w and 75 w booster modules available. change mi-2xx-xx to mi-bxx-xx. product grade operating temp. i = -40? to +85? m=-55 ct o +85? p arameter product grade i- grade m - grade storage temperature -55? to +100? -65? to +100? operating temperature (baseplate) -40? to +85? -55? to +85? p ow er cycling burn-in 12 hours, 25 cycles 96 hours, 200 cycles t emperature cycled with power off 12 cycles 12 cycles 17? per minute rate of change -65? to +100? -65? to +100? t est data supplied at these temperatures* -40?, +80? -55?, +80? w arranty 2 years 2 years environmental compliance mil-std-810 mil-std-810 derating navmat p-4855-1a navmat p-4855-1a output voltage z= 2 v t = 6.5 v n = 18.5 v y= 3.3 v r = 7.5 v 3 = 24 v 0= 5 v m = 10 v l = 28 v x= 5.2 v 1 = 12 v j = 36 v w= 5.5 v p = 13.8 v k = 40 v v= 5.8 v 2 = 15 v 4 = 48 v mi-200 03/04 2 of 2
|
